STANCOR OIL MINDER® SIMPLEX & DUPLEX PUMP AND CONTROL SYSTEMS

The Stancor Oil-Minder® Control and Pump System allows water to be automatically
pumped from elevator pits, transformer vaults, and industrial sumps without danger
of ejecting potentially harmful oily substances into sewers, rivers and waterways.
There is no need for a separate oil-water separator. The product is engineered for
efficient and trouble free pumping, even under the most severe conditions. The
Stancor Oil-Minder® System is the overwhelming choice among design engineers and
compliance authorities worldwide, and has a proven record for protecting valuable
equipment and the environment.


Features:

NEMA 4x watertight corrosion resistant polycarbonate enclosures
Stainless steel sensor probe with patented electronic technology that repels dirt
contamination
Single direct plug-in power source for operation of entire system
Solid state components
Alarms, lights, silence switch, and remote monitoring circuit for oil, high liquid, and
high amperage conditions
Solid state "push to test" switch conveniently performs all pump and control
diagnostic tests
Complete factory assembly and testing insures quality of entire pump and control
system
Patented - Pat. #4,715,785, #4,752,188, #6,203,281 and others pending
Oil-Minder® System can be combined with a variety of different pumps and valves
Choice of: 115v or 220v (1 phase) OR 230v/460v/575v (3 phase)
LED indicator lights for oil spill, power, high liquid level, overload, and pump run
UL 508 and 778 approved
ENTELA tested and approved as a system
“There Is Only One Oil-Minder® System and Stancor Makes It”
Quality You Can Believe In

Description of Stancor Simplex Oil-Minder® Systems

The Stancor Simplex Oil-Minder® System is available in two primary configurations,
as follows:

The Multi-Option Oil-Minder® System is designed for easy, fool-proof installation. All
pump and control cables are factory wired into a wall mountable junction box.
Between the junction box and the main Oil-Minder® control panel is a multi-pin
quick connect cable. This single cord, 8-pin system allows the electrical cable between
the junction box and control panel to be run through conduit and interconnected up
to 250 feet long, using a single "push and turn" motion. There is no need for field
wiring. Electrical installation costs are reduced by approximately 75% and all
connections are secure and water-tight.

The Junior Oil-Minder® System is a good choice where the main control is located in
the same area as the pump pit, or where the main control will be located remotely and
conventional "hard wiring" is used between a junction box and the main control.
Comparative features of each model are as follows:
1. Stancor Model SE-50 submersible effluent pump .5 HP, 115 volt, 3600 RPM, 2”
discharge connection
2. Check valve (2”)
3. Stancor Oil-Minder 115V, 1Ø control system with built-in audible and visual alarm
when pump does not
run due to oil in pit or high liquid or high amperage condition. Provide silencing
button for audible alarm
built into panel. Panel shall have two contacts for a remote alarm location (one each
for oil and high water
or amperage alert). Junction box will be provided with multi-pin connector and cord in
lengths as required,
25 ft. standard, optional 25 ft. increments.
4. Junction box will be provided with multi-pin connector and cord in lengths as
required; 25 ft. is standard,
optional 25 ft. increments available up to 250 ft.
5. All buried pump pressure discharge piping shall be protected with tape coat CT
corrosion protection tape
6. Pump cable, probe cable, high liquid alarm cable, and pump “on” float cable (16 ft.
lengths)
7. High liquid alarm float with clamp device to mount to pump discharge piping
8. Pump On/Oil Alert float
9. Power cord and molded ground plug (6 ft. length)
10. "Push to Test" switch for diagnostic check of all pump control and power functions
ITEMS 1, 3, 4, 6, 7, 8 AND 9 PROVIDED BY STANCOR AS A STANDARD PACKAGE